|
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
||||
|
||||
My Pig
I thought I would update my thread with details of the build
Engine: Cosworth forged pistons, pins and circlips Cosworth forged rods and bolts Cosworth piston rings Cosworth metal head gaskets Cosworth big end bearings Cosworth main bearings Cosworth valve spring set Sleeved Block Cosworth AVCS 278/10.7mm camshaft set ARP head stud kit Subaru timing belt Subaru gasket kit Subaru rocker cover set Torque plate bore and hone Serviced heads/new valve guides, stem seals, recut seats, facing, porting, fit cams/springs, acid bath and set tappet clearance 05 Decaps TD05 20G Turbo GFB Stealth bov Process West FMIC and CAI GT Spec Headers (Jet Coated) Samco Silicon turbo intake Hyperflow Oil catch can 3" TBE Magnaflow Boost control solenoid ECU MoTeC ver9 PNP board Drive by wire AVCS Advanced functions Wideband Lambda Suspension and Stopping Power: G4 Coilovers Front and Rear 22mm sway bar and drop links Antilift kit Whiteline roll centre kit Willans 4 point harness DBA5000 rotors Endless cc-Rg Cosmetics: STi Recaro Racing Seat Rays 57 Maximum Gramlights 18" Rims Falken RT615 rubber Delta Dash Power: A few of my favourite pics. Dam Buster Cruise Photo thanks to Jester.
__________________
[COLOR="Red"]I have the right foot of Subaru death![/COLOR] [SIGPIC][/SIGPIC] 365hp and 515nm New Beast to arrive April 2015 - 365hp, 450nm, 0-100 in 4.4sec. AMG Goodness! Last edited by BOMB3R; 27-06-2008 at 05:09 PM. |
#2
|
||||
|
||||
Looking hot J. Good fitment on the FMI, HUGE improvement, its just a bit of a shame about the endtanks, is it the process west? Becuase if so i thought you could keep most CAI's with it?
Rims look teh pr0n, what are they? And also i have one of the short bits from Inlet to airbox in blue coming in if you want it for nothing?
__________________
PerthWRX - Where gay singles meet! Last edited by WRPI0; 15-12-2006 at 03:02 PM. |
#3
|
||||
|
||||
that cooler is HEAPS better
like the rims too good job jaron
__________________
I AM WE TODD DID... I AM SOFA KING WE TODD DID... |
#4
|
||||
|
||||
Looking much nicer Jaron.
Intercooler piping seems a lot shorter too! Now post up them dyno sheets
__________________
[COLOR="Gray"]550Nm off a 2L... Just wish it was in the dak dak...[/COLOR] |
#5
|
||||
|
||||
much much much better Jaron, huge improvement. Looks well 'ard now
they finished ripping the ground up out the front of your work ?
__________________
MY93 Impreza GX 1.8L, 0hp, 0nm |
#6
|
||||
|
||||
FMIC looks much better Jaron 217.6Kw aye??? Time for a grudge match
__________________
05 STi Spec C Type Ra 04 LL Bean Outback |
#7
|
||||
|
||||
Cheers guys! Dynos sheets now up
__________________
[COLOR="Red"]I have the right foot of Subaru death![/COLOR] [SIGPIC][/SIGPIC] 365hp and 515nm New Beast to arrive April 2015 - 365hp, 450nm, 0-100 in 4.4sec. AMG Goodness! |
#8
|
||||
|
||||
Those rims and rubber sure look mean!
Nice work! |
#9
|
||||
|
||||
Thats some nice numbers up there, well done.
Next move, the Motorplex? |
#10
|
||||
|
||||
Looks nice Jaron.
What's the full mod list champ? When you going to get it down to Speedworks for a run on the hub dyno?
__________________
you mirin? |
Tags |
pig |
|
|