|
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
Mounts for 4 Point Harness
I want to mount eye bolts for 4 Point Harness in Rear Parcel Shelf to allow easy clip in/clip out of harness.
Are there any suitable mount points, that dont require rear seat to be removed each time you want to access the eye bolts? Baby restraint points etc? Must be lots of people that have installed these? Any advice welcomed. Cheers Tim |
#2
|
||||
|
||||
Parcel shelf will require doubler plates as a minimum to have enough strength for a harness. The baby seat mounts are not designed for a harness.
Options are: Meridian Motorsport Harness Bar which sits above your parcel shelf: Custom Race Fabrication, Roll Cages, Harness Bars, Seat Mounting etc. Put the eylets inbetween the seat cushions. This is pretty close to iffy as the angle of the harness is not ideal, but still legal. Just pull the seats out, only takes a few minutes to do. Then you can get into the debate of how safe it is to run a harness without roll over protection. A lot of people won't run with a harness unless there is a roll over bar, half cage, full cage etc due to the way the roof crumples and the lack of movement in a harness.
__________________
[COLOR="Gray"]550Nm off a 2L... Just wish it was in the dak dak...[/COLOR] |
#3
|
|||
|
|||
Its only 10 minute job to remove the seat,Plus the removal of the back seat makes the car sound awesome from inside
|
#4
|
||||
|
||||
Maximum Motorsport Do the rings for harness attachment. Give them a call.
__________________
Have Fun. |
#5
|
||||
|
||||
I have my harnesses mounted and the rear seat in place.
You can remove the seat, put the eyelet bolts in, replace the seat. It does fit. Rather than removing the seat to unclip when I am not using the harnesses I simply leave them clipped in and place them under the floor mats in the rear passenger footwells.
__________________
[COLOR=RoyalBlue][B][I]Titanium Reinforced[/I][/B] MY00 Impreza WRX | MY11 Liberty GT Premium[/COLOR] |
#6
|
||||
|
||||
This is on Nauli's car done by MMS and also going to be done on mine soon ish once i get time.
Eye bolts can be unscrewed and rear seat be bolted back on. Pic courtesy of Birthday boy(yesterday) Daniel at MMS and Steve's car hope you guys dont mind.. Uploaded with ImageShack.us
__________________
Chinese Mexican [SIGPIC][/SIGPIC] |
#7
|
||||
|
||||
Nauli told me that the seat goes straight back on without having to take off the eyelet bolts.
__________________
Fuck your signature |
#8
|
||||
|
||||
In that case even better also have pics of the bottom mount for the side belts but cant seem to find it...
__________________
Chinese Mexican [SIGPIC][/SIGPIC] |
#9
|
||||
|
||||
Quote:
__________________
2016 Subaru Outback - Work Wagon 350NM of CVT Goodness Pit Crew, shit talker. |
#10
|
||||
|
||||
Quote:
...and seat removal and replacement are 5 minute jobs...
__________________
No Subarus currently owned |
Tags |
harness, mounts, point |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Race Harness - 3" Six Point | nauli | For Sale | 1 | 24-09-2011 01:47 PM |
FS Brand new 6 point harness | fatboy | For Sale | 16 | 03-02-2011 04:13 PM |
FS: 4 Point RPM Harness & STi Belt Pads | GETAGRIP | For Sale | 2 | 16-01-2008 02:41 PM |
Willans 4 point racing harness (red) with anchor bolts | Wilmo | For Sale | 6 | 15-10-2007 05:48 PM |
F.S Air flow meter, Pod filter, cheap 4 point harness | WhiteRX | For Sale | 6 | 11-04-2007 10:48 PM |