|
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
Steering knuckle install
Could any of you lads recommend a good workshop to help me install an STI steering knuckle on a MY11 wrx?
Need the clearance for the Invidia downpipe I'm about to order! |
#2
|
||||
|
||||
http://www.perth-wrx.com/vb/mechanic...workshops.html
How much is the knuckle worth? By the time you factor in the Invidia system, the knuckle, the labour to put it in... does it come close to getting a custom exhaust made up?
__________________
[I]trolololol[/I] |
#3
|
|||
|
|||
Thanks!
The knuckle was quoted to be $60, and the downpipe $600. I'm not too sure about the labour costs that would be involved with the knuckle install though. It would be charged hourly I assume? Any ballpark figures on the labour cost? It apparently takes 2-3 hours to put in STI knuckle... |
#4
|
||||
|
||||
Where did you source the knuckle from?
__________________
[COLOR=Black]Liberty GT Spec B tuned 240 HP & 372 Nm at the hubs.[/COLOR] "Instead of banning high performance cars - ban low performance drivers" |
#5
|
||||
|
||||
Would love to know also as I am planning on ordering an Invidia TBE in the new year. Steering knuckle, exhaust and H brace will hopefully be completed in one foul swoop.
|
#6
|
||||
|
||||
S Technic in Maddington always does good work.
For your info -we have the MY11 sedan complete TBE stainless steel exhausts arriving tomorrow - if needed can supply dump pipe only - these are developed with S Technic for our right hand drive cars so there is no need to fudge the steering knuckle with ours. Just install - fits spot on as it is made for AUS spec - not USA spec. Going to be a market leader on the pricing too! I will upload a youtube link when I get a chance Will be posting them up on the website and forum over the new few days once the container is unpacked and I can take some pictures of them Cheers Rob
__________________
ULTREX PERFORMANCE best bang for your buck in performance parts www.ultrex.com.au |
#7
|
|||
|
|||
I called up Prospeed Racing today, and they told me that they could supply one for an extra fee of $60, so I think that is acceptable.
What kind of design is the downpipe Rob? 3 inch? Divorced or bellmouth? |
#8
|
||||
|
||||
Its a 3 inch dump - flared mouth design - a bell mouth tends to hit the steering knuckle on RHD so we have a smooth flowing flared mouth design in order to NOT hit the steering knuckle.
This system is 3 inch and then reduced to 2.5 where it splits in to 2 pipes - then twin tip mufflers
__________________
ULTREX PERFORMANCE best bang for your buck in performance parts www.ultrex.com.au |
#9
|
||||
|
||||
They sound just as good as they look
__________________
2015 Forester XT Premium 2020 VW Tiguan Allspace teejay: If I wanted a comeback Id wank in front of a fan |
#10
|
|||
|
|||
Well called up a few places today asking for labour quotes, and it roughly comes up to $500 for the knuckle and Invidia downpipe install.
Do you guys reckon that's worth it? Or should I just go with another brand that doesn't require the STI knuckle? |
Tags |
install, knuckle, steering |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Subaru STI Steering Wheel Knuckle | iceken | Wanted | 3 | 06-12-2011 08:59 PM |
Steering knuckle | scuba | Wanted | 2 | 02-06-2011 01:12 PM |
Steering shake after H Brace install | Fable | Mechanicals | 7 | 24-04-2011 06:38 PM |
Steering Wheel Audio Controls | jacox | General Subaru Discussion | 9 | 17-06-2007 10:56 AM |
RA GC8 Steering rack? will it work on GC8 WRX | POLARBEAR666 | Mechanicals | 2 | 24-11-2005 07:15 PM |