|
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
||||
|
||||
Replace one faulty injector, or replace whole set?
Hi guys,
This might seem like a really stupid question, but I have tried using search so here we go. I've had an injector fail on cylinder #2 dumping raw fuel into it from the moment the key is turned on. A workshop has confirmed this and has the faulty injector out of the car. Now originally they thought it was 2 injectors and that I would need a whole set to match instead of just replacing the 2. Now that it is only 1 injector I am looking for some opinions. Should it be fine to replace a single injector, or do I really need to throw out a whole set? Injectors in question are ID1000cc. Thanks in advance for help.
__________________
MY08 WRX 325hp/456nm/18psi E85 |
#2
|
||||
|
||||
I think its safer to replace whole set.
I have my eyes on a set of bosch 850 cc plug and play injectors, 380 shipped. Apparently, ID doesn't flow test and match injectors before pack them up, only DW, bosch, and most japanese brands do. Correct me if im wrong. using the Perth-WRX mobile app
__________________
MY08 STI 422whp at 1.5bar on E85, built by Diversion Garage, assembled and tuned by EvoR Update from new owner: 375whp at 1.4bar on 98, at Tokyo Motorsport |
#3
|
||||
|
||||
Reference to back this up? ID are modified bosch injectors.
__________________
[SIGPIC][/SIGPIC] |
#4
|
||||
|
||||
Do the set. You want them flow matched.
__________________
MY00 WRX. 89 Prelude. 99 CRV |
#5
|
||||
|
||||
Yep, just going to suck it up and take the cost. Shame as the injectors are only 4 months old.
s2052xxx: "We only sell matched sets, and within each set the dynamic flow rate (slope) will vary no more than +/- 1%, and the dead time (offset) will vary no more than +/- 20 microseconds which is equivalent to +/- 1% at a pulsewidth of 2 milliseconds." Injector Dynamics " ID1000cc Injectors suit WRX 08-11 - Pro Speed Racing
__________________
MY08 WRX 325hp/456nm/18psi E85 |
#6
|
||||
|
||||
Just out of curiosity, did u get a flow test sheet?
using the Perth-WRX mobile app
__________________
MY08 STI 422whp at 1.5bar on E85, built by Diversion Garage, assembled and tuned by EvoR Update from new owner: 375whp at 1.4bar on 98, at Tokyo Motorsport |
#7
|
||||
|
||||
Not that I can recall, but I didn't pay much attention to them as I wasn't fitting them.
__________________
MY08 WRX 325hp/456nm/18psi E85 |
#8
|
||||
|
||||
Warranty? Id be contacting them.
__________________
Huge range of extinguisher brackets for cars! http://kap.industries/ |
#9
|
||||
|
||||
Yeah, I have contacted them and the response was less than satisfactory in my mind. I have been advised it needs to be sent to their U.S testing facility where it can be checked for defects and fixed/replaced. I will be doing this, but obviously can't sit around without a car for weeks on end while waiting.
__________________
MY08 WRX 325hp/456nm/18psi E85 |
#10
|
|||
|
|||
Quote:
Where did you buy them from? direct from the UA or here in Aus from a re-seller? If you got them direct then unfortunately you will have to send them back to them..if you got them locally then the issue is the seller responsibility. |
Tags |
faulty, injector, replace, set |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
WTB: Stock TMIC & airbox set up MY99 | SPOOLED | Wanted | 0 | 05-04-2006 11:29 PM |
Set of windows | Bakks | Wanted | 0 | 27-01-2006 04:56 PM |
Rear STI Lateral Link Set - GC8 or GD Wagon | geoff | For Sale | 0 | 15-07-2005 09:06 PM |