Hi guys,
i have just installed a power fc into a MY00.I have done the wire swap, it powers up,but when i did a sensor check i found 3 sensors showing fault


AIRFLOW METER SENSOR
THROTTLE POSITION SENSOR
BOOST SENSOR

Car wants to start but can't.If i put the factory ecu back in it starts straight up..

What do you guys think, car sensors.power fc settings or the power fc its self...
i bought it second hand in japan..

i have reset power fc to..

Any help would be good...thanks

Cue Rossco.

__________________
Signarape!

First off:
Have you swapped the cam & crank sensor wires only on the BLUE plug?
(pins 5 & 6)


Can you please post what part number your power fc is?
Also what firmware version does it say under 'ETC' - Prog. Version?

Can you please post the voltages for your MAF & TPS from the SENSOR Check page.

MAIN MENU-> ETC -> SENSOR SW / CHECK:
Look for any sensor names highlighted in BLACK background or any flashing sensors. Any highlighted in black indicates a problem. The engine check light will also stay on if any of the sensors aren't working (highlighted in black). This is not to be confused with the black DOT switch on / off sensors.



Next thing highlight "ETC" and then choose "FUNCTION SELECT".

BOOST CNTL KIT <- Make sure the boost controller is ENABLED (ON) (your WRX won't start if it isn't!)
AIRFLOW WARN - Disable airflow warning
INJECTOR WARN - Enable/Disable injector warning
KNOCK WARNING - Enable/Disable Knock warning
02 F/B CONTROL - Disable 02 feedback

__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER]
[CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER]

Yeah have swapped the right wires..

AIRFLOW METER shows .3v
THROTTLE POSITION SENSOR shows 0v
BOOST SENSOR shows 0v

on the hand controller

they are also hi lighted in black which according to the manual means a fault..

pin 5 and 6 were swapped

Ej 207
power fc v 6.30
fc commander
ver 3.21

Boost cntl turned on?

Run an extra earth from the block (a/c compressor mount to the Negative on the battery, GC's develop earthing issues)

__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER]
[CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER]

YES
have tyred on and off
on now

will try a/c compressor mount to the Negative on the batter

sorry ninja edit:

Run an extra earth from the block (a/c compressor mount to the Negative on the battery, GC's develop earthing issues)

__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER]
[CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER]

Ok tried an extra earth from the block but it still shows 3 faulty sensors on the hand controller.. Any other ideas....

Pull the case off the power Fc & look for burnt tracks or water damage.

__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER]
[CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER]