|
|||||||
 |
|
|
LinkBack | Thread Tools | Display Modes |
|
#41
20-03-2012, 07:30 PM
|
||||
|
||||
Happy days!
Perhaps the 99-00 PFC's don't throw a CEL due to their factory map having a higher pressure ceiling & apexi have changed the software to suit on those models? I don't have an additional Map sensor on mine (nor have any that I've tuned) & never had that CEL/boost kit issue pop up. Even on the Datalogit user group there was no mention of it. Happy the additional MAP sorted your issue.
__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER] [CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER] 
|
|
#42
20-03-2012, 07:39 PM
|
||||
|
||||
|
Quote:
PFC's flash the CEL for: Knock value over set threshold (35 is default) MAF @ >4.95 volts 100% injector duty (Flashes are all different patterns) CEL stays lit with ignition on for: Crank/ cam trigger open circuit Ignition driver fault (Pfc internal) Injector driver fault (Pfc internal) Missing sensor input or sensor over voltage
__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER] [CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER]
|
|
#43
20-03-2012, 07:55 PM
|
|||
|
|||
|
Quote:
There did not seem to be much info on my particular issue. The boost cut side of things, when the boost kit was off. Hopefully this thread will help people on both PWRX & anyone else who searches for it. Thanks again for the information & advice Rossco & T to the J.
__________________
Cheers, Simon.
|
|
#44
20-03-2012, 08:13 PM
|
||||
|
||||
|
Quote:
__________________
I am only an asshole on the internet :) [SIGPIC][/SIGPIC]
|
|
#45
20-03-2012, 08:20 PM
|
|||
|
|||
|
Will break the gearbox with a new clutch
__________________
Cheers, Simon.
|
|
#47
20-03-2012, 08:38 PM
|
|||
|
|||
|
Its a 3 bar sensor, I think the the advertised limit is 1.8 bar of manifold pressure.
__________________
Cheers, Simon.
|
|
| Tags |
| fc, map, power, sensor, upgrade |
|
|
LinkBacks (?)
LinkBack to this Thread: http://www.perth-wrx.com/vb/mechanicals/47871-map-sensor-upgrade-power-fc.html
|
||||
| Posted By | For | Type | Date | |
| Upgrade Your Power | This thread | Refback | 12-03-2012 04:22 PM | |
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Co-Pilot brings Auto tuning & Launch control to the Power FC! | Rossco | Apexi Power FC Discussion | 12 | 26-05-2012 02:23 PM |
| 98-99 sti power fc | sinizter | For Sale | 2 | 21-02-2012 11:55 AM |
| power fc with hand controller | 69terra69 | For Sale | 5 | 31-07-2011 06:10 PM |
| what power fc | officer_Farva | Apexi Power FC Discussion | 13 | 13-06-2011 09:58 PM |
| Power fc sensors faults | WRXmy00 | Mechanicals | 17 | 27-02-2011 07:34 PM |
3Likes
its all good under 19 psi though & I honestly think it would be on par with my STI down the 1/4. God it feels quick.........
Linear Mode
