|
|
LinkBack | Thread Tools | Display Modes |
#1
|
||||
|
||||
DIY: Process West CAI Install MY11 STI
So I thought I'd post up what I've been doing this morning. Tried to put it in the DIY bit, but it wouldn't let me. If this is deemed worthy, maybe it can get moved there?
I picked up American Dave's unused Process West CAI a couple of weeks ago. I was unsure if I should swap it over without a tune, so I decided to remove the stock air box and measure the inlet pipe diameter to see if it was the same size as the PW one. It is exactly the same, so I decided to go ahead and install the new one. I'll get a tune later when the exhaust goes on Stock intake removal - just a couple 10mm nuts and a couple push clips and it all comes out: Old one out - who needs all that junk? New one ready to go in Measured old and new - exactly the same except for the straightening vanes in the stock housing. But then it does have to turn the air through 90°, whereas the PW tube means the air will be flowing straight already. 70mm, same as the stock one Then, to fit the block off plate, you have to remove the wire clips in the wheel arch area, as they will be going into the block off plate and you'll need to use one of those holes (the one on the right of shot) to fix the block off plate and the other one at the top near the yellow sticker Here I thought I'd be able to fit it all from within the engine bay, but unfortunately you can't hold the back of the fixing bolts as they're below the block off plate. So off came the front bumper (gave me a good excuse to change out the Hella relay from the GB) Then, just connect up the hoses and swap the MAF sensor over. Job done! Can't tell any difference in power, but the NOISE! Oh the NOISE, it's wonderful. Now I know I really do have a turbo UPDATED: Having lived with this mod for a few days now, I have actually noticed a DROP in acceleration at low/medium revs, with some hesitation around 3400rpm. Therefore, I will be returning back to the stock intake for now until I can get the exhaust & tune done. Getting quotes now for Race Torque ECUTEK and ASG Verso.
__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER] [CENTER]Car - [FONT=Verdana][COLOR=dimgray][B]MY11 WRX STI Spec R + Recaros [/B]- 284HP|394Nm|Ultrex 3"TBE|PW CAI[/COLOR][/FONT][/CENTER] [CENTER]Bike - [COLOR=red][FONT=Verdana][B]MY10 Honda CBR1000RR Fireblade [/B]- 171HP|114Nm|Yoshi CF Slipon[/FONT][/COLOR][/CENTER] [CENTER]My other passion - facebook.com/[FONT=Verdana][COLOR=dimgray][B]JamieWebsterPhotography[/B][/COLOR][/FONT][/CENTER] Last edited by STIMUL8IN; 28-06-2012 at 05:34 PM. Reason: Updated with new info |
The Following User Says Thank You to STIMUL8IN For This Useful Post: | ||
BOMB3R (28-06-2012) |
Tags |
cai, diy, install, my11, process, sti, west |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Diy boot install | tris7an | Cosmetic | 116 | 06-06-2012 05:03 PM |
MY11 STI vs Tomtom vs HTC Desire HD | siaw | General Subaru Discussion | 15 | 10-04-2011 06:34 PM |
Genuine Road Registered Version 4 STi TypeR V-Limited Coupe #274/1000 | JDM | For Sale (Cars Only) | 4 | 03-12-2010 09:49 AM |
Process West Front mount Intercoolers | Darren | The Former Workshops Forum | 1 | 26-04-2006 03:13 PM |