Perth-WRX.com  

Go Back   Perth-WRX.com > Technical > Mechanicals
Register Diddy Kart ArticlesAll AlbumsBlogs FAQ Members List Calendar Search Today's Posts Mark Forums Read


Welcome to Perth-WRX, click here to register!

Like Tree1Likes

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 08-03-2014, 09:36 PM
Scoobie Noobie
Member
 
Join Date: Oct 2013
Location: Perth
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
choppa at standard level
Default Cam tensioner interferance?

So im changing the idlers, cam belt and tensioner on my 1990 EJ20T.
But the tensioner that I took off is fowling on the crank case as you can see in the pics. The new one (which is exactly the same) seems to fowl as well and when I hold it (the new one)in position over the mount bolt holes it only seems to sit flush when pushed all the way to the right. As I slide it to the left as recommended, the lip where the pin hole is, hits the case almost immediately.
Can anyone advise they have seen this and whats the solution as if I leave it all the way over to the right I doubt the cam belt tensioner idler wont have the necessary tension on it.
I suspect I will need to grind the case slightly, has anyone done that ?
Cheers for any help,,
Mark
Attached Thumbnails
IMG_2923.JPG   IMG_2924.JPG   IMG_2925.JPG   IMG_2926.JPG  
Reply With Quote
  #2  
Old 08-03-2014, 11:59 PM
STI Master
Member
 
Join Date: Jan 2014
Location: WA
Posts: 529
Thanks: 63
Thanked 57 Times in 48 Posts
amtrapid knows their stuff
Default

They can hit there if forced to the left before tightening and releasing the pin best way to avoid it is to make sure the bolts are finger tight enough that the tensioner can slide from right to left once belts in place and all the idlers are on push the tensioner across with a screwdriver don't use a pry bar or be heavy on it it should move with relative ease .
Tighten the bolts to hold it in the left position and use a torque wrench to specs otherwise you will pull the thread. . Then remove the pin holding the piston .The crushing of the tensioner usually happens when some one is heavy handed with a prybar trying to push the tensioner to the left because they pulled the pin out before realizing that it has to be moved across and tightened beforehand .

Last edited by amtrapid; 09-03-2014 at 12:01 AM.
Reply With Quote
  #3  
Old 09-03-2014, 12:06 AM
Scoobie Noobie
Member
 
Join Date: Oct 2013
Location: Perth
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
choppa at standard level
Default

Thanks Mate
Ill give that a shot
Reply With Quote
  #4  
Old 09-03-2014, 12:08 AM
STI Master
Member
 
Join Date: Jan 2014
Location: WA
Posts: 529
Thanks: 63
Thanked 57 Times in 48 Posts
amtrapid knows their stuff
Wink

Torque specs are first 17 ft lbs then 20 ft lbs for those two bolts on the tensioner.
Reply With Quote
  #5  
Old 11-03-2014, 10:00 PM
Scoobie Noobie
Member
 
Join Date: Oct 2013
Location: Perth
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
choppa at standard level
Default

Thanks Amtrapid

I put the new tensioner on today and it could barely move 1mm left or right.
But it seemed to be all the way over to the right looking at the bolts relation to the slots. So i ground the housing a little, now it will move about 3 or 4mm to the left. That should work as it will move a similar amount as the old tensioner but without crushing the lip.

On another note my cam wheels seem to all sit still and line up freely with no tension on them. The book seems to imply the left cams will be on lobes and need to be held in place, is this normal.











Reply With Quote
  #6  
Old 11-03-2014, 10:37 PM
STI Master
Member
 
Join Date: Jan 2014
Location: WA
Posts: 529
Thanks: 63
Thanked 57 Times in 48 Posts
amtrapid knows their stuff
Default

The drivers side of the engine cams hold still and move with little resistance . The passengers side generally move off the marks when the belt is removed as they are on the lobe of the cam in the marked position .Top intake cam should only be wound clockwise to reline up and bottom exhaust cam only wound anti clockwise to reline up as per the manual as this is an interference engine design.
I use a breaker bar and socket to hold the cam in place as I put the belt on then if the belt is kept taught while you run it over the top and bottom cam wheel as well they usually hold in place just with the belt and some slight tension from your hand on the belt as it is put on . Start the belt on the drivers side first then work across the top over the passengers side and down. The manual outlines this.
If there is no tension on the passengers side cam wheels that moves them off the timing marks sounds like something is wrong . Only the drivers side is off the lobes and stays exactly where you put it.
Do you have a manual it clearly has diagrams and fully explains it if you follow its hard to go wrong . Once the belt is on dont turn the engine till you count the teeth between timing marks as outlined in the manual to make sure you spot on and not a tooth out.
Reply With Quote
  #7  
Old 11-03-2014, 11:02 PM
STI Master
Member
 
Join Date: Jan 2014
Location: WA
Posts: 529
Thanks: 63
Thanked 57 Times in 48 Posts
amtrapid knows their stuff
Default

This should help.

Click image for larger version

Name:	20140311_225852.jpg
Views:	9
Size:	1.49 MB
ID:	12360

Click image for larger version

Name:	20140311_225917.jpg
Views:	7
Size:	896.3 KB
ID:	12361

Click image for larger version

Name:	20140311_225935.jpg
Views:	7
Size:	1.09 MB
ID:	12362

Click image for larger version

Name:	20140311_225946.jpg
Views:	7
Size:	992.3 KB
ID:	12363

Click image for larger version

Name:	20140311_225958.jpg
Views:	8
Size:	1.67 MB
ID:	12364
Reply With Quote
  #8  
Old 12-03-2014, 08:28 AM
matto20v's Avatar
STI Master
Member
 
Join Date: Jul 2005
Location: Perth
Posts: 950
Thanks: 38
Thanked 36 Times in 33 Posts
matto20v at standard level
Default

I am sure you know this,

But you're missing an idler on the drivers side.
Reply With Quote
  #9  
Old 12-03-2014, 08:52 AM
Scoobie Noobie
Member
 
Join Date: Oct 2013
Location: Perth
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
choppa at standard level
Default

Quote:
Originally Posted by matto20v View Post
I am sure you know this,

But you're missing an idler on the drivers side.
Yep I havent finished the job yet, thanks.


Amtrapid, I do have the manual and yes I can see it says to rotate the cams.
Strangely they didnt move when I released the old belt. And they have all stayed in the exact same spot. I will check today if there is any tension on that side (passenger) cams. Seems not so far.
Ive had that engine in my car for about 16 years and it still runs great. Strange. I will count the teeth today as you suggest.
Cheers
Mark
Reply With Quote
  #10  
Old 12-03-2014, 05:40 PM
STI Master
Member
 
Join Date: Jan 2014
Location: WA
Posts: 529
Thanks: 63
Thanked 57 Times in 48 Posts
amtrapid knows their stuff
Default

How did you go mate all sorted ?
Reply With Quote
Reply

Tags
cam, interferance, tensioner

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Wtd: A/C belt tensioner bracket ej22.. kayarubin Wanted 0 18-04-2011 04:16 PM
Video: Choose Your Own Cam with 2011 Subaru WRX STI rally car rss.feed General Subaru Discussion 0 13-01-2011 05:30 PM
WTB: Cam Wheels Suite EJ20 JA50N Wanted 11 09-05-2008 04:02 PM
o ring in t belt tensioner... dan.r.s Mechanicals 2 18-07-2007 08:04 PM
Speed cam spotted 8th may 2006 AC Schnitzer Non-WRX Discussion 9 08-05-2006 11:26 PM



Welcome to Perth-WRX, click here to register!

All times are GMT +8. The time now is 07:42 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO