Perth-WRX.com  

Go Back   Perth-WRX.com > Off Topic Discussions > Non-WRX Discussion
Register Diddy Kart ArticlesAll AlbumsBlogs FAQ Community Calendar Today's Posts Search


Welcome to Perth-WRX, click here to register!

Like Tree19Likes

Reply
 
LinkBack Thread Tools Display Modes
  #41  
Old 21-08-2010, 06:30 PM
DZENCI's Avatar
WRX Hi Five Club
Member
 
Join Date: Nov 2007
Location: Perth
Posts: 269
Thanks: 7
Thanked 10 Times in 10 Posts
DZENCI at standard level
Default

Just a few pics when it all started. Got it from rolla forum on my build thread on there, somehow it works.


This is the part of the dash my mate fabricated, its a bar which is welded above the transmission tunnel and the side pillars where the old dash plate was spot welded. This bar is much more stronger than the old dash plate and should hold the front part of the car a bit more hopefully and avoid any rattling like the old dash did.






1.0mm Thick plate for the dash face


The 3 left side gauges are facing the driver with the plate dropped in 25mm on the right side to give the angle to the driver.
Holesaw cut-outs for the gauges to fit




OLD DASH! what it looked like and how it should look now..

We've test fitted the gauges to see how the angle of the 3 gauges on the left are towards the driver. So far everything is good and now a top part of the dash and a console is to be made and then dress everything up with padding then black suede and store away. Gives a nice clear view of each gauge facing the driver.

Last edited by DZENCI; 21-08-2010 at 06:56 PM.
Reply With Quote
  #42  
Old 21-08-2010, 06:32 PM
DZENCI's Avatar
WRX Hi Five Club
Member
 
Join Date: Nov 2007
Location: Perth
Posts: 269
Thanks: 7
Thanked 10 Times in 10 Posts
DZENCI at standard level
Default

So far new dash has been all dressed up and ready to bolt on when its time to put the interior side of things together.
As for the interior thats it, just had to get this made before respraying took place so the fresh paint doesn't get ruined after.

Just a pick with how it looks with the gauges sitting in








Also just had the machining of the engine done at Southside Engine Centre:







Bored and honed to 86.5mm
Line-honed main journals
Blueprinted/balanced crankshaft/rods

Just took in the new clutch kit along with billet flywheel and ross harmonic balancer to get it all balanced out than the assembly will take place along with top end .
Reply With Quote
  #43  
Old 21-08-2010, 06:33 PM
DZENCI's Avatar
WRX Hi Five Club
Member
 
Join Date: Nov 2007
Location: Perth
Posts: 269
Thanks: 7
Thanked 10 Times in 10 Posts
DZENCI at standard level
Default

So far the bottom end is ready to put together.
Still got to get it all cleaned up properly to get rid off any metal bits from machining than slowly will get assembled.

Im very happy with Southside's for their work, everythings come up nice and flat.

Here are all the bits along with the block...















Reply With Quote
  #44  
Old 21-08-2010, 06:36 PM
DZENCI's Avatar
WRX Hi Five Club
Member
 
Join Date: Nov 2007
Location: Perth
Posts: 269
Thanks: 7
Thanked 10 Times in 10 Posts
DZENCI at standard level
Default

here is the fully assembled bottom end, yet i've got to sort the cylinder head but still got to choose the best combo for it.

the machining job is no1, thanks to southside engine centre for that.



Last edited by DZENCI; 21-08-2010 at 06:55 PM.
Reply With Quote
  #45  
Old 21-08-2010, 06:38 PM
DZENCI's Avatar
WRX Hi Five Club
Member
 
Join Date: Nov 2007
Location: Perth
Posts: 269
Thanks: 7
Thanked 10 Times in 10 Posts
DZENCI at standard level
Default

well, its about time I got the car back all freshly painted in the original factory colour.
Very happy with the bare metal paint job. The surface rust in the engine bay is finally gone and now all you can see is a straight engine bay in one colour and no rust spots.








SHE ALSO LOOKS A LITTLE MORE FAT WITH THE NEW CUSTOM PURSUITIES AND TIRES THAN BEFORE





Few evening pics




THE FINAL FINISH CLOSE UP, PICTURE PERFECT REFLECTION FROM DRIVER SIDE DOOR WITH ZERO DENTS




Slowly I've started to assemble the rear end starting off with the rear bumper and tail lights and install sound deadening in the boot and the shelf than eventually get the inside of the car done. The difference is very noticable from before and after installing the sound deadener, will definetely ipmrove cabin noise compare to before and make it a little more quieter.



Also have took out the front steering components to install all new tie rods, ball joints, whiteline bushes through out, pretty much got everything that i can change to improve the steering geometry. The steering should be much more responsive than before. All the old joints have split and lost grease so were pretty much useless.

Last edited by DZENCI; 24-08-2010 at 12:38 AM.
Reply With Quote
  #46  
Old 21-08-2010, 06:40 PM
DZENCI's Avatar
WRX Hi Five Club
Member
 
Join Date: Nov 2007
Location: Perth
Posts: 269
Thanks: 7
Thanked 10 Times in 10 Posts
DZENCI at standard level
Default

The rear shelf is now complete with sound deadener. Still cant believe the difference this stuff makes and it's the same thickness as normal dynamat.



Thats how the interior stands now. Have cleared out all the things I dont need and started cleaning it up. Have to grab some dry ice tomorrow in order to get rid off the old sound deadener before I lay down the new one.

Give's me a head ache looking at it at this state, long way to go yet.



Reply With Quote
  #47  
Old 21-08-2010, 09:32 PM
Flat Four Father
Member
 
Join Date: Dec 2005
Location: Kewdale
Posts: 2,077
Thanks: 3
Thanked 65 Times in 48 Posts
seagull knows their stuff
Default

what brakes are you going to run ?
Reply With Quote
  #48  
Old 21-08-2010, 09:54 PM
mARC's Avatar
Perth WRX Old Skool Cool Dude
Member
 
Join Date: Aug 2007
Location: In a House
Posts: 3,589
Thanks: 43
Thanked 30 Times in 28 Posts
mARC at standard level
Default

Was it Brian from SSE that sorted you out? Top guy, not caught up with him in a while, so unsure if he's even still there.

Orange A9X Torrana, may or may not be running NOS
__________________
[SIGPIC][/SIGPIC]
Reply With Quote
  #49  
Old 22-08-2010, 03:55 AM
DZENCI's Avatar
WRX Hi Five Club
Member
 
Join Date: Nov 2007
Location: Perth
Posts: 269
Thanks: 7
Thanked 10 Times in 10 Posts
DZENCI at standard level
Default

Quote:
Originally Posted by mARC View Post
Was it Brian from SSE that sorted you out? Top guy, not caught up with him in a while, so unsure if he's even still there.

Orange A9X Torrana, may or may not be running NOS

It's Graham and Neil. I know Graham has been a part of the company for years and took over ownership.
They're a bit pricey but it was worth the money with all the machinig they done for me. Definitely recommend them.

Not sure about the orange Torana but I Know Graham is the one who has been race prepping John Zappia's HQ race car.
Last time I was there he had a billet big block that cost $20k ex USA for Zappia's engine build.
Reply With Quote
  #50  
Old 22-08-2010, 04:13 AM
DZENCI's Avatar
WRX Hi Five Club
Member
 
Join Date: Nov 2007
Location: Perth
Posts: 269
Thanks: 7
Thanked 10 Times in 10 Posts
DZENCI at standard level
Default

Quote:
Originally Posted by seagull View Post
what brakes are you going to run ?

Currently it's running the rx7 4 pots and 2 pot rears. It's got individual wilwood brake-fluid reservoirs for front and rear.They're pretty good ATM. Might change to something else down the track.

That's them there
http://memimage.cardomain.com/ride_i...0004_large.jpg
Reply With Quote
Reply

Tags
corolla, grandpa, sleeper, spec, turbo


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




Welcome to Perth-WRX, click here to register!

All times are GMT +8. The time now is 07:33 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO