|
|
LinkBack | Thread Tools | Display Modes |
#41
|
||||
|
||||
Should also mention that it only hot 28psi from 4th gear onwards.
__________________
The one perkent... Last edited by Tony; 25-06-2015 at 12:25 PM. |
#42
|
||||
|
||||
Yes correct its not hitting that level until WOT in 4th/5th/6th.
|
#43
|
||||
|
||||
So you went from ~20psi to 24psi on a stock 207, disregarding hypereutectics for a 20hp gain.
I agree with Jack here, 267hp still seems very low for 1.7bar of boost.
__________________
06 STi: 337hp @23psi on E85... 06 STi: 309hp @22psi on 98ron... |
#44
|
||||
|
||||
Even with my 2grams of fuck all of knowledge of how things work, I would think that is even worse and that your boost target is set at 2bar in the tune. So it gets to 28 and holds there for a bit?
__________________
06 STi: 337hp @23psi on E85... 06 STi: 309hp @22psi on 98ron... Last edited by RJ999; 25-06-2015 at 12:38 PM. |
#45
|
||||
|
||||
I'm no tuner but arnt tunes done in 4/5th gear and that's where your waste gate duty is generally set up? Rossco might have more knowledge on this.... Therefore the fact it is spiking 28 should be adjustable on dyno ..
However... Load on dyno prob hasn't been set to match street driving .. More load more boost basicly using the Perth-WRX mobile app |
#46
|
||||
|
||||
Here we go again... Where's matto
|
#47
|
||||
|
||||
Nice boost spike..... Then the typical VF turbo 'out of breath' pitch over at 6000rpm....
I don't reckon that's a 2 bar spike though.
__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER] [CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER] |
#48
|
||||
|
||||
Quote:
I'm buying a tactrix cable shortly so I can start learning more about this tuning business. Noob tuning question: let's say i wanted to trim the boost a little bit. I know this is done via WGDC table. But will this have any flow on effects that require other parts of the tune to be tweaked like afr or timing? i.e. can I trim just WGDC a little and be done with it? Last edited by dnbosiris; 25-06-2015 at 02:39 PM. |
#49
|
||||
|
||||
I'm not an open source tuner by any means.
Your system may have a base WG duty cycle plus a boost target look up index & PID tables but I'm not sure. You'd be better asking someone who knows OS tuning more thoroughly.
__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER] [CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER] |
#50
|
||||
|
||||
I've had the same situation when I got my car back from the tuner, stock internal ej205 just with a vf-34 and supporting mods boost set at '22psi' but when hitting WOT in 4th and 5th my boost gauge reads 24psi.
Called the tuner up and asked why it seems to be reading higher boost level in those gears and all I got back was 'yeah that's fine no problem at all' so been trying to do some re-search on this and can't seem to find a whole heap! using the Perth-WRX mobile app |
Tags |
safe boost, threshold, vf35 |
|
|