|
|
LinkBack | Thread Tools | Display Modes |
#21
|
|||
|
|||
Quote:
It is a good turbo and will cost less than the 34, purely for popularity reasons. Its a great street turbo IMO. I have attached a LINK to my thread from the Verso tune. The dyno charts from the stock STI dyno run & overlay of the Verso tune done. The stock run was at 1.2 ish bar, after the tune it was @ 1.6 bar. You can see it comes on hard and fast and has great low - mid range grunt but dies off at the top end. This is exactly how it felt to drive. You were needing to change gears at about 6500 rpm, as from about 6000 onwards you could feel the pull drop off. This was at the drags of course The VF34 would move the chart lines to the right a bit & it would get you another 45 ish hp running the 1.6 bar boost pressure. The VF35 is just a idea I threw out there, as not many people think of it. I am not talking it up, I am just stating the facts, that it is a good, low cost turbo for an upgrade to a WRX. Is THIS not a TMIC on the Vortex?
__________________
Cheers, Simon. |
#22
|
||||
|
||||
^ now i regret not buying your 35 you sold yours for $370, sounds very cheap or is that what they are worth?
also the 34 is ball bearing where the 35 is not im sure when reading the turbo sticky?
__________________
98 gf8 Rip |
#23
|
|||
|
|||
I guess they are only worth, what someone is willing to pay. I still think you will be able to pick one up much less than a 34. That is if both turbos are in identical condition of course.
There was a 35 on another site only a few days ago. They were asking $700 for it, but it had only done 15,000ks or something. Its sold now, not sure what he ended up getting for it. 35 has thrust bearings and 34 is ball bearing. The 34 is without a doubt better than the 35. But people seem to overlook the 35, its still a good low - mid range turbo. Better stop blabbering on now in this guys thread....
__________________
Cheers, Simon. |
#24
|
|||
|
|||
Cool, thx for the info. Well this is going to be my first turbo engine and i don't really want to go with cams, mods $1000 turbo's, 1.6 bars of boost, Power FC, etc and all this really great but expensive gear.
What i really wanted is just above normal, maybe a slightly bigger turbo, better ECU like if possible a plug and play STI one. I definitely don't want to blow the engine. FMIC basically because i also don't think a top mount will fit under the bonnet. Quote:
Without going with all the good mods you suggested and staying pretty much stock, is a boost controller and a higher rating waste gate actuator necessary? Would a cat less 3inch dump pipe be a good idea for me? Last edited by Guyph_01; 31-07-2011 at 01:38 PM. |
#25
|
||||
|
||||
tbe: turbo back exhaust
cai: cold air intake dump is part of the tbe and yes it will be good allows better breathing like if you had bigger lungs
__________________
98 gf8 Rip |
#26
|
|||
|
|||
Ok thx, For the TBE, what specs? Full 3 or 2.5, 3' dump and 2.5 ??? And the CAI, Do i need one or not? Is that those silicone things? |
#27
|
||||
|
||||
normally for turbo cars 3'' all the way
cai the pod that sits in your guard with the piping
__________________
98 gf8 Rip |
#28
|
|||
|
|||
Oh so CAI is basically a pod filter and the end of a pipe that replaces the factory air box and is place somewhere where it gets cold air?
|
#29
|
||||
|
||||
pretty much, like in the guard usually. i just have a pod filter and run ducting to the pod. also im custom making something from my top side vent scoop from ultrex for more air
__________________
98 gf8 Rip |
#30
|
||||
|
||||
Thought of using a WAIC off an RS? Don't you have one laying around the place?
Would be about as efficient as a stock TMIC without the lag of the FMIC. |
Tags |
ecu, info |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
will STI ECU plug into non STI? | Ca6139uY | Stock ECU Discussion | 16 | 03-06-2014 10:11 AM |
ECUTech ECU for MY06/MY07 STi | nathonm | For Sale | 4 | 30-10-2010 04:24 PM |
Human Biology ECU Uni Books - NEW! | B4GT | The Quokka | 1 | 12-01-2009 06:20 PM |
03,04 & 05 AUS WRX STi Ecu code help | waxdass | Other ECU Discussion | 5 | 15-07-2008 06:07 PM |
ECU FAQ - What's available | pmh | ECU Discussion | 1 | 22-07-2007 03:56 PM |