scary spec - Page 7 - Perth-WRX.com

scary · #61 01-02-2012, 08:40 AM

Quote:

Originally Posted by Jimmy S

Awesome Shano!!!

For the record, I think you are better off with the straight exit turbo and the different pipe to the TMIC! It's less restrictive IMO

I'm with you on the turbo too mate so I think I may have lucked into that......BUT turbo hasn't turned up so It may not all get done before the tuner goes back to sydney

Very touch and go at the moment ....or I will have to cut my losses and go Verso

ewrxion87 · #62 01-02-2012, 09:21 AM

im missing out on the MMS tune on 1st 2nd 3rd of Feb...so im going to Racetorque as they have been helping MMS anyways. They are a fully authorised dealer. MMS also agreed with this. Wisby was the best.

apart from that - great ride mate. I installed the PW intercooler yesterday and you wont be disappointed.

Quote:

Originally Posted by scary

OK so change of plan today

Ordered from Troy at Prospeed

BBK-M
Walbro
Unequal length Headers
Process West TMIC
Silicon inlet pipes

Carmods Aus

Grimm Speed 3 port solenoid.

Hopefully it can all be here for when the tuner comes over from NSW to tune at MMS (left it a bit late) or I will have to go and see Sean and get the ECUTek taken off and go Verso.

Fingers crossed these BBK turbos are all they are cracked up to be

RUSSGT · #63 01-02-2012, 11:27 AM

Never understood how you will install those headers with that big bar across them!

scary · #64 01-02-2012, 02:34 PM

Quote:

Originally Posted by RUSSGT

Never understood how you will install those headers with that big bar across them!

ha ha ha ha

scary · #65 01-02-2012, 02:39 PM

BBK-M aka blouch turbo has arrived.......phew

Quality looks good - hopefully it lives up to expectations

Exhaust has been ported as seen in the pics

ewrxion87 · #66 01-02-2012, 02:44 PM

keep us updated mate, American dave has recommended i do the same upgrade. Would be sweet to see the results.

are you installing it yourself ?

Quote:

Originally Posted by scary

BBK-M aka blouch turbo has arrived.......phew

Quality looks good - hopefully it lives up to expectations

Exhaust has been ported as seen in the pics

GTB Liberty · #67 01-02-2012, 03:12 PM

Quote:

Originally Posted by RUSSGT

Never understood how you will install those headers with that big bar across them!

Quote:

Originally Posted by scary

ha ha ha ha

I must be missing something cause I have often wondered myself?

The bar is for shipping only and gets removed?

NB - I've never had headers installed on a dak dak.

scary · #68 01-02-2012, 03:15 PM

Quote:

Originally Posted by GTB Liberty

I must be missing something cause I have often wondered myself?

The bar is for shipping only and gets removed?

NB - I've never had headers installed on a dak dak.

Bar is just to hold them together for transport

rmove and fit to headers to car

scary · #69 01-02-2012, 03:44 PM

Quote:

Originally Posted by ewrxion87

are you installing it yourself ?

If MMS have room for me tomorrow and tie to tune friday then yes I will install myself.

If not I'll get MMS to fit.

As far as Race Torque............probably not

ewrxion87 · #70 01-02-2012, 04:00 PM

not a fan? i havent been there yet... should i not go there ?

Quote:

Originally Posted by scary

As far as Race Torque............probably not

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
For Sale: MY04 spec C conversion	shamrock	For Sale (Cars Only)	5	14-08-2011 06:40 PM
04 Spec C for Sale	UNDRGND	For Sale (Cars Only)	9	03-06-2011 07:24 PM
Subaru WRX STI Spec C launched in Japan	rss.feed	General Subaru Discussion	1	28-12-2010 01:20 PM
Difference between a Jap spec engine and a aus spec	FiveT	General Subaru Discussion	4	28-01-2008 11:32 AM
Blitz DSBC Spec S (Electronic Boost Controller)	D34THROW	For Sale	0	20-11-2005 11:19 PM