The [RETSEJ] project - Page 19 - Perth-WRX.com

jEstEr? · #**181** 10-08-2007, 01:53 PM

if its a straight swap then there is hardly any work involved at all, unfortunately this is a rather unique conversion and as such we are learning as we go

a month or two back i lent a hand in converting a 1996 STi RA into a 1996 LX wagon.. drove in NA on friday, drove out turbo on monday. when you do a year:year conversion everything fits... as for putting a 2006 motor into a 1993 shell with a 1996 loom, a 2006 loom, a 2003 ecu etc.. it becomes a bit of a headache

DarkMoose · #**182** 10-08-2007, 02:13 PM

but its fun

, what total weight are u aiming for Mattus? You getting any braces welded in / harness bar? Also i notice the cusco braces that run at the foot well in rear seats, why not do a diy job :P. Shame no more handbrake up foot to the floor action when its awd

markveron · #**183** 10-08-2007, 02:38 PM

major headache

jEstEr? · #**184** 25-09-2007, 01:08 PM

small update. emailed motec asking where my new version of the m800 pnp was

Quote:

Originally Posted by motec

Hi Matthew,
We have just started production of the WRX OEMS of the 06 and 07 cars. At this stage we have several ECUs in the field for testing and evaluation if no problems are found then it will be released.
The cost of an OEM changeover is normally around $400 but in this case you would also need to have the variable cam and drive by wire upgrades enabled which cost $330 and $380 respectively.
If you are local and keen to go ahead with an OEM installation on your car let me know and I can make some arrangements with a dealer for you to get one of the pre production units. Full release would be expected in November.
If you have any further questions feel free to call or email.

Pity I'm not farkin local to Victoria or i'd be in there like a shot. This also means anyone waiting for a MoTeC for their Liberty Tune By STI will be waiting too

BOMB3R · #**185** 25-09-2007, 01:19 PM

Fark Matt! I remember when it was going to be ready for MV07

MV08 is looking doubtful

American Dave · #**186** 25-09-2007, 01:37 PM

Quote:

Originally Posted by jEstEr?

small update. emailed motec asking where my new version of the m800 pnp was

Pity I'm not farkin local to Victoria or i'd be in there like a shot. This also means anyone waiting for a MoTeC for their Liberty Tune By STI will be waiting too

oh great there goes that option huh!

jEstEr? · #**187** 25-09-2007, 01:39 PM

it was never going to be ready for MV07

BOMB3R · #**188** 25-09-2007, 01:43 PM

My Bad it was Dutton I was thinking off

DarkMoose · #**189** 25-09-2007, 02:29 PM

U're bad jaron! PS mat, i'm sure u will get it sorted asap, u now have a nice set of coilovers

geoff · #**190** 26-09-2007, 08:59 PM

Hi Mat,

I look forward to seeing this car in Stace's shed on the lift when I'm back for a visit in '09

g.

LinkBacks (?) LinkBack to this Thread: http://www.perth-wrx.com/vb/general-subaru-discussion/9598-%5Bretsej%5D-project.html
Posted By	For	Type	Date
1HZ Turbo thread - Page 9	This thread	Refback	13-08-2011 03:05 PM