|
![]() |
|
LinkBack | Thread Tools | Display Modes |
#1
|
||||
|
||||
![]()
What can i use to re-seal my intake manifold?
Sorry im not much of a genious with mechanics
__________________
MY01 WRX Turbo-back exhaust Turbosmart vaccum lines Turbosmart boost gauge Turbo Timer Its a work in progress ;) IF IN DOUBT FLAT OUT!! |
#2
|
||||
|
||||
![]()
what did you pull it off for?
__________________
![]() JDM version 3 STi RA |
#4
|
||||
|
||||
![]()
had to replace turbo intake pipe
and tuna is that a joke?
__________________
MY01 WRX Turbo-back exhaust Turbosmart vaccum lines Turbosmart boost gauge Turbo Timer Its a work in progress ;) IF IN DOUBT FLAT OUT!! |
#5
|
||||
|
||||
![]()
You don't need any sealant for the intake manifold.
If you are worried about leaks, clean the mounting surfaces and replace the 2 intake manifold gaskets and torque down the bolts correctly.
__________________
RS Liberty - Because WRX's are only good for parts... |
#6
|
|||
|
|||
![]()
lol haha yeah he is serious i use that all the time it is even better for exhaust manifolds lol Super glue is good to. But seriously maybe try a set of manifold gaskets????
|
#7
|
||||
|
||||
![]()
have already started car and its leakin from the intake manifold... it sounds like a very lumpy v8 then stalls
__________________
MY01 WRX Turbo-back exhaust Turbosmart vaccum lines Turbosmart boost gauge Turbo Timer Its a work in progress ;) IF IN DOUBT FLAT OUT!! |
#8
|
||||
|
||||
![]() Quote:
Brent. ![]()
__________________
* [REXPLOIT] - EJ207 2.2L build. Under assembly: * All Sling - No Bling: Member 002: * WRX Club of WA member / CAMS member / CAMS registered volunteer: [SIGPIC][/SIGPIC] |
#9
|
||||
|
||||
![]()
Hard not to use "incredibly stupid" along with "wrxii" and "your next post will be, "what is this knocking sound'"" in the same post without sounding like an asshole........So this is the best I could do.
![]()
__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER] [CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER] |
#10
|
||||
|
||||
![]()
haha rossco
__________________
![]() JDM version 3 STi RA |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
WTB- Idle Control Solenoid (on intake manifold) | Dubs | Wanted | 3 | 04-04-2009 01:48 AM |
GC8 intake manifold | damo | Mechanicals | 5 | 24-10-2008 05:45 PM |
08 WRX & Plastic Intake manifolds | WRXTASY | Mechanicals | 9 | 26-07-2007 08:42 PM |
sti intake manifold and tmic | Shurman | Mechanicals | 2 | 29-03-2007 05:46 PM |
MAtch porting intake manifold | UNDRGND | Mechanicals | 2 | 08-08-2006 12:06 AM |