Looks awesome!!! Now to install the overlays.. To be honest it's not that hard.. but it IS a two person job and very fiddly.

__________________
2016 Levorg GT-S
Old man spec.

Looks good!
Glad the instructions helped.
Is there a small gap between the new trim and the rear gate?

__________________
2015 Forester XT Premium
2020 VW Tiguan Allspace
teejay: If I wanted a comeback Id wank in front of a fan

Looks a lot better. I have a spare one (thanks Soksta) that I'll get painted and chuck on. Going to do the overlays first though.

__________________
[I]trolololol[/I]

thanks mate, im pretty happy. Depending on how fussy i get and how much time i have i might take it off and adjust it...i think its 1.5mm up on one side causing it to sit funny...its only 4 bolts and interior off so il have a look at it. overlays go on Monday $50 to have them installed but at least il know its done right. Tune is now on Friday as racetorque had a couple silly issues this morning with ecutek and the new firmware thats out sad for me but id rather it done right.

__________________
Ewrxion87

P-West TMIC / ecutek / HF CAI / Turbosmart / Apexi / Federal / 19psi / bc racing & whiteline / Perrin Performance / Rays

Fark!! $ 50.00 is good considering how much f*cking around there is. I'm tempted to order some more and do them again PROPERLY. LOL Looking forward to seeing how they look when installed??

__________________
2016 Levorg GT-S
Old man spec.

Yea, Yusree from protec Tinting is Ozzy park, has done all my cars for me and he said its an hours work so just pop in. $50 is more then exceptional and at least he will have the eye for detail.
i will post pics on completion. im worried because i dont have flared guards like the new models..the look may be let down a little but see how we go. then jsut to get this tune downand save up for some rims and a few months time. slowly but surely

__________________
Ewrxion87

P-West TMIC / ecutek / HF CAI / Turbosmart / Apexi / Federal / 19psi / bc racing & whiteline / Perrin Performance / Rays

these will most likely be next - with a set of federal 595rpm

not sure how well the +45 offset will sit but il find out, otherwise a set of Rota dpt's will be going on. I think for extra $250 the Enkei would be better ?

__________________
Ewrxion87

P-West TMIC / ecutek / HF CAI / Turbosmart / Apexi / Federal / 19psi / bc racing & whiteline / Perrin Performance / Rays

Depends how wide you're going with the rim. 7.5"-8" might not come out as much as you would like but 8.5"-9" at +44/45 might go alright.

__________________
[I]trolololol[/I]

They only come in an 8" rim for the 5x100 bolt pattern.


From stock, they will extend a further 23mm out. They also do a +35 offset as well in the 5x100 bolt pattern according to their website (I tried to find a set but had no luck) which will add another 10mm width from the +45.

HUggy,

arent stock rims +48 offset ?

so wouldnt that mean i'd only be 3mm in width of benefit to the guards ? as it being an 8inch rim doesnt that mean it just goes deeper into the car towards the diff etc... ? and the lower offset means outwards towards the kerb ?

is my understanding wrong ?

shame only an 8 inch rim, im starting to think Ultrex Classic's might be the better alternative ? 8 at +42

__________________
Ewrxion87

P-West TMIC / ecutek / HF CAI / Turbosmart / Apexi / Federal / 19psi / bc racing & whiteline / Perrin Performance / Rays