|
|
LinkBack | Thread Tools | Display Modes |
#21
|
||||
|
||||
I have a sr20
Im on 400Nm with VF37 keen for more, still stock 207 which has done 110k km
__________________
Chinese Mexican [SIGPIC][/SIGPIC] |
#22
|
||||
|
||||
Cheers for the feedback lads. Will ring Race Torque and ask Lane about headers + re-installing my CAI along with a retune.
Don't know if should run anymore boost on a stock 255 (17/18psi atm). On a side note meth injection has always intrigued me....maybe another time.
__________________
65.3 short track (wet). Getting better. Still somewhat retarded. |
#23
|
||||
|
||||
Tune dependent Shane - I've been running 19psi with no known issues since the tune.
My torque figure is reasonably substantial considering the OEM cat back exhaust.
__________________
[COLOR=Black]Liberty GT Spec B tuned 240 HP & 372 Nm at the hubs.[/COLOR] "Instead of banning high performance cars - ban low performance drivers" |
#24
|
||||
|
||||
Unopened EJ205.. lots of boost and standard headers. Still going strong.. Last edited by Intra; 07-09-2012 at 08:37 AM. |
#25
|
||||
|
||||
What turbo Intra?
__________________
Huge range of extinguisher brackets for cars! http://kap.industries/ |
#26
|
||||
|
||||
Also remember you are trying to compare hub dyno to roller dyno. There is a difference!
Tbh, 360ish newts on a 2.5L is piss weak. A dyno reads the torque and calculates your power from there. Torque is everything. Post up your graph again (I cbf searching ) as it seems laggy. FYI: Power (kW) = (Torque x RPM x 2 x Pi) / 60,000 is what the dyno calculates. Given your low torque max value you can see why its not giving you the 'kick' you want.
__________________
[COLOR="Gray"]550Nm off a 2L... Just wish it was in the dak dak...[/COLOR] |
#27
|
||||
|
||||
Yes, it's in my driveway thread/dyno chart. Had 354nm, added UELs, EBC and TMIC, gained a bit over 10hp & 32nm
__________________
[I]trolololol[/I] |
#28
|
||||
|
||||
No replacement for displacement i think. Mine and daves rides are 2.5's and seem to develop larger torque easier but seem to fades as the rpm gets too high, downside is lower peak hp, but upside it the cars dont have to be whipped like a stray cat to access the power band, where the 2.0L's make higher peak HP but need to be spinning like a demon.. that is the key to small displacement engines anyways,high rpm. I think looking at the latest tech twinscroll stetup from a reputable source would be a good place to start! 257, zorst, flash 441nm at 4000rpm :P
__________________
06 sti |
#29
|
||||
|
||||
That's my dyno sheet.
TD05: Butler TBE, STI panel filter, AVO silicone inlet, Grimspeed BCS, Walbro, Blouch TD05-18G, Process West TMIC, ID 725cc injectors Run done in 4th gear TD04 for reference: Butler TBE, Walbro pump, nothing else. Run done in 3rd gear
__________________
65.3 short track (wet). Getting better. Still somewhat retarded. Last edited by monkeee; 07-09-2012 at 09:45 AM. |
#30
|
||||
|
||||
E85 an option or is it a daily?
That will give you a real fat band of torque.....
__________________
[B][COLOR=red]Jerk of the circle.[/COLOR][/B] |
Tags |
required, requiredyes, torque, whore |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Opinions/Suggestions needed: Increasing response + torque curve | monkeee | Mechanicals | 23 | 15-06-2011 03:01 PM |
Wanted to Borrow: Torque wrench. | Evidencee | Wanted | 0 | 29-06-2009 10:05 PM |
Build for Torque | SilentKilla | Mechanicals | 18 | 23-04-2007 09:51 PM |
Bolt torque | urabus | Mechanicals | 0 | 22-11-2006 07:04 PM |
MRF Wins Asia Pacific Rally 2005 - Race Torque | thx | Non-WRX Discussion | 5 | 31-10-2005 12:41 PM |