|
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
||||
|
||||
Yayy! I like.
__________________
Air is for pussies. |
#2
|
||||
|
||||
Very Nice, and you did all this on the floor too!! May i ask who your using as the builder? Might be heading down this path soon!
|
#3
|
||||
|
||||
Neil Herbert @ The Engine Exchange is doing it all for me.
__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER] [CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER] |
#5
|
||||
|
||||
Quote:
i was going to have it powder coated but it will turn out too glossy (so I'm told?). I need to find a matt red to suit...... P.s: Stace the cams look flawless too.
__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER] [CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER] Last edited by Rossco; 26-12-2010 at 11:11 AM. |
#6
|
||||
|
||||
There's been a couple of WTF's!! along the way.......
1. 3 of 4 inlet manifold bolts on the RH side were literally finger tight!!??!! 2. Charcoal canister purge solenoid nipple was broken off (& someone had tried to super glue it back on...lol) 3. Charcoal cannister vapor line from fuel tank fractured along RH chassis rail (underbonnet) 4. Wiring - Cam sensor harness had rubbed through the insulation in one spot due to longterm vibration & insufficient support. 5. Silicone reseal of fail on RH rocker cover gasket. 6. Missing nut on dump pipe (lowest one). 7. RH front inner cv boot split. 8. Mystery red wiring along LH wiring loom.
__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER] [CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER] |
#7
|
||||
|
||||
I believe they are referred to as "holiday surprises" Ross.
__________________
Air is for pussies. |
#8
|
||||
|
||||
ha ha lol^^
Sick em wrx used to service it.....
__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER] [CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER] |
#9
|
||||
|
||||
Ohhh. Well that explains it. Give me some time, if I can find the highly agricultural excuse for a ic sprayer tank that once lived on my car, I'll post a picture of it.
__________________
Air is for pussies. |
Tags |
build, engine, rossco |
|
|
LinkBacks (?)
LinkBack to this Thread: http://www.perth-wrx.com/vb/mechanicals/39184-rosscos-engine-build.html
|
||||
Posted By | For | Type | Date | |
b4 engine vs Gen 4 engine • club.liberty.asn.au | This thread | Refback | 24-02-2014 02:08 AM | |
old_duwel's 99 STI RA Limited #450/1000 - Page 106 - Subaru Impreza GC8 & RS Forum & Community: RS25.com | This thread | Refback | 28-05-2011 04:14 PM | |
old_duwel's new GC8 - Page 106 - Subaru Impreza GC8 & RS Forum & Community: RS25.com | This thread | Refback | 17-05-2011 11:16 PM |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Trainwrex Engine build back | trainwrex | General Subaru Discussion | 6287 | 27-03-2017 10:50 PM |
Engine Build - Advice Requested | STI325V6 | Mechanicals | 31 | 17-05-2014 07:05 AM |
Opinions from those that know? engine build.... | Rossco | Mechanicals | 131 | 21-12-2012 09:01 PM |
My Engine Build - Under Way | STI325V6 | Mechanicals | 71 | 26-05-2011 09:19 AM |
New Engine Build Questions | Qu3xy | Mechanicals | 44 | 02-03-2009 07:34 PM |